Ball Valves

Advantages of Ball Valves
Single Piece
Two Piece
Three Piece
Hydrant

Please contact
Anderson-Brooksbank USA, LLC
for a full Brochure and Data Manual

Advantages of Ball Valves

• trunnion mounted designs permit much larger sized and higher pressures
• enormous size range to DN 600
• pressure classes from Class 150 through Class 600
• non-resilient and metal seats extend temperature range to 1000° Celsius
• environmental protection and emission control techniques widely available
• all end connections
• infinite choice of materials of construction in combination with design options and choice of seating
• manual, pneumatic, hydraulic and electric operators
• top entry designs facilitate field inspection and maintenance
• one-piece bodies minimize potential leak paths
• taper seating permits wide temperature cycling and reduces wear
• basic and advanced cavity pressure relief systems
• erosive and viscous media easily handled
• seat modifications for low Dp conditions
• ball control valves deal with simple throttling and complicated process control systems
• international standards guarantee worldwide conformity and interchangability
• cryogenic and vacuum capacity
• valves may be prepared for special services and be jacketed

Top

Single Piece

End Entry Standard Type

• Reduced Bore
• Supplied in Gunmetal BS 1400 (LG4)
  Aluminum Bronze BS 1400 (AB2)
  Aluminum BS 1490 (LM6)
  Duplex
  Hastelloy
  Titanium
• 25-150mm nominal bore
• Class 150 and 300
• Flanged BS, ANSI and DIN standards
• PTFE seats and seals
• Peek or Delrin seals supplied for high temperature applications
• Blowout proof stem
• Locking facilities for open and closed if required
• Antistatic if required
• Stainless steel or Monel trim if required

Top Entry Standard Type

• Full and reduced bore
• Supplied in Gunmetal BS 1400 (LG4), (LG2)
  Aluminum Bronze BS 1400 (AB2)
  Aluminum BS 1490 (LM6)
  Duplex
  Hastelloy
  Titanium
• 10-125mm nominal
• Class 150
• Trunnion mounted ball
• PTFE seats and seals
• Peek or Delrin seals supplied for high temperature application
• Blowout proof stem
• In line maintenance
• Antistatic
• T-bar handle
• Manual and actuated

Wafer Standard Type

• Full and reduced bore
• Supplied in Gunmetal BS1400 (LG4) Aluminum Bronze BS1400 (AB2)
  Aluminum BS1490 (LM6)
  Duplex
  Hastelloy
  Titanium
• 1/2" - 6" nominal bore
• Class 150
• Flanged to BS, ANSI and DIN standards
• Floating ball design
• PTFE seats and seals
• Peek or Delrin seals supplied for high temperature applications
• Blowout proof stem
• Antistatic if required
• Locking facilities for open and closed if required
• Bodies- Sizes up to and including 3" have a screwed insert design of body. Flanged connecting holes are drilled at clearance diameter. Size over 3" have bolted construction design bodies. Flanged connecting holes are tapped.

Two Piece

Standard Type

• Full bore
• Supplied in Gunmetal BS1400(LG4) Aluminum Bronze BS1400 (AB2) Duplex
  Hastelloy
  Titanium
• 25 - 200 mm nominal bore
• Class 150 and 300
• Flanged to BS, ANSI and DIN standards
• Floating ball design
• PTFE seats and seals
• Peek or Delrin seals supplied for high temperature applications
• Blowout proof stem
• Antistatic if required Stainless steel or Monel trim if required
• Lloyds and MOD approved
• Locking facilities for open and closed
• Easily actuated with air, hydraulic or electric actuators

Three Piece

Standard Type

• Full and reduced bore
• Supplied in Gunmetal BS 1400 (LG4), (LG2) Aluminum Bronze BS1400 (AB2) Aluminum BS 1490 (LM6) Duplex Hastelloy Titanium
• 6-150mm nominal bore
• Class 150 and 300
• Screwed NPT, BSP, brazed, capillary brazed or flanged to BS, ANSI and DIN standards
• Floating ball design
• PTFE seats and seals
• Peek or Delrin seals supplied for high temperature applications
• Blowout proof stem
• Fire tested to Department of Transport standards
• Lloyds and MOD approved
• Locking facilities for open and closed
• Easily actuated with air, hydraulic or electric actuators
• Antistatic if required
• Stainless steel or Monel trim if required

Hydrant Valves

Straight Way Screwed
and Brazed Connections

Sizes 40mm-65mm (1-½" - 2-½") nominal bore

Bodies Cast in either gunmetal BS 1400 (LG4) or aluminum bronze BSl400 (AB2)

Ends Available screwed BSP, NPT and socket brazed

Hose Coupling Standard to BS336, other hydrant ends are available on request

Stem Anti-blowout stem as standard in aluminum bronze. Monel or stainless steel on request

Balls Manufactured as standard in either gunmetal BS1400 (LG4), aluminum bronze BS1400 (AB2). Monel or stainless steel on request

Seats Manufactured by Brooksbank in virgin PTFE as standard, Peek and Delrin seals can be supplied for high temperature applications.

Stem Seals PTFE 25% GF

Locking Facilities Valves can be locked open and closed if required

Our quality assurance system is assessed to International Standard ISO9002 and to British Standard 5750 Part 2.

All materials and finished valves can be fully certified in accordance with DIN 50 049.1B

Straight Way
Flanged Connections

Sizes 40mm-65mm (1½" - 2½") nominal bore

Bodies Cast in either gunmetal BS1400 (LG4) or aluminum bronze BS1400 (AB2) Ends Available flanged to BS, ANSI or DIN standards

Hose Coupling Standard to BS336, other hydrant ends are available on request

Stem Anti-blowout stem as standard in aluminum bronze. Monel or stainless steel on request

Balls Manufactured by Brooksbank in virgin PTFE as standard, Peek and Delrin seals can be supplied for high temperature applications.

Stem Seals PTFE 25% GF Locking Facilities Valves can be locked open and closed if required

Quality Assurance Our quality assurance system is assessed to International Standard ISO9002 and to British Standard 5750 Part 2.

All materials and finished valves can be fully certified in accordance with DIN 50 049 3.1B

AngleType Screwed
or Brazed Connections

Sizes 40mm-65mm (1½") nominal bore

Bodies Cast in either gunmetal BS1400 (LG4) or aluminum bronze BS1400 (AB2)

Ends Available screwed BSP, NPT and socket brazed

Hose Coupling Standard to BS336, other hydrant ends are available on request

Stem Anti-blowout stem as standard in aluminum bronze. Monel or stainless steel on request

Balls Manufactured as standard in either gunmetal BS1400 (LGA), aluminum bronze BS1400 (AB2). Monel or stainless steel on request

Seats Manufactured by Brooksbank in virgin PTFE as standard, Peek and Delrin seals can be supplied for high temperature applications.

Stem Seals PTFE 25% GF Locking Facilities Valves can be locked open and closed if required

Our quality assurance system is assessed to International Standard ISO9002 and to British Standard 5750 Part 2.

All materials and finished valves can be fully certified in accordance with DIN 50 049 3.1B.

Angle Type
Flanged Connections

Sizes: 40mm-65mm (1½" to 2½") nominal bore

Bodies: Cast in either gunmetal BS1400 (LG4) or aluminum bronze BS1400 (AB2)

Ends: Available flanged to BS, ANSI or DIN standards

Hose Coupling: Standard to BS336 other hydrant ends are available on request

Stem: Anti blowout stem as standard in aluminum bronze. Monel or stainless steel on request.

Balls: Manufactured as standard in either gunmetal BS1400 (LG4), aluminum bronze BS1400 (AB2). Monel or stainless steel on request.

Seats: Manufactured by Brooksbank in virgin PTFE as standard, Peek and Delrin seals can be supplied for high temperature applications.

Stem Seals: PTFE 25% FG

Locking Facilities: Valves can be locked open and closed if required.

Our quality assurance system is assessed to International Standard ISO9002 and to British Standard 5750 Part 2.

All materials and finished valves can be fully certified in accordance with DIN 50 049 3.1B

Top

Single Ball Class 150

Single Ball Class 300

Two Piece Screwed Ends

Wafer Ball Class 150

Straight Way Hydrant
Screwed and Brazed
Connections

Straight Way Hydrant
Flanged Connections

Angle Type Hydrant
Flanged Connections

Angle Type Hydrant
Screwed or Brazed
Connections